Differences

This shows you the differences between two versions of the page.

--- tools:general_wood:clearance [2023/11/24 15:36] – smartin015
+++ tools:general_wood:clearance [2024/02/07 23:31] (current) – smartin015
@@ Line 1: / Line 1: @@
-====== General Woodworking Proficiency Based Clearance ======
+====== General Woodworking Clearance ======
 {{section>tools:clearance_template&noheader&nofooter}}
-====== Tool Specific Instruction ======
+{{section>tools:general_wood:clearance_area&nofooter&noindent}}
+====== Dust Collector ======
 ===== Point out the following tool features =====
-Drill Press
-  * Maintenance tag
-  * Power switch
-  * Feed handle
-  * Depth stop adjust
-  * Table lock
-  * Table vertical adjust crank
-  * Motor tension locks & lever
-  * Speed change belts
-  * Speed settings chart & diagram
-Belt/disk sander
-  * Maintenance tag
-  * Power switch
-  * Sanding belt
-  * Sanding disk
-  * Rotation indicators
-  * Dust gate
-  * Table angle locks & gauges
-  * Belt tension/tracking lever
-  * Belt cleaning eraser
-Spindle Sander
-  * Maintenance tag
-  * Power switch
-  * Throat plates
-  * Spindles
-  * Spindle washers
-  * Spindle change thumbscrew
-Scroll Saw
-  * Maintenance tag
-  * Power switch
-  * Blade holder/tensioner
-  * Presser foot
-  * air assist
-  * Plate angle adjust knob & gauge
-Miter Saw
-  * Maintenance tag
-  * Power switch
-  * Dust gate
-  * Horizontal slide lock lever
-  * Blade down locking pin
-  * Depth stop adjust
-  * Blade roll adjust pin
-  * Blade yaw adjust lock
-  * Hold down clamp
-  * Keep out zone
-Bandsaw
-  * Maintenance tag
-  * Dust gate
-  * Power switch
-  * Belt cutter & welding system (bonus points)
-  * Belt tension adjust
-  * Blade height lock wheels
-Dust Collector
   * Power switch
@@ Line 77: / Line 13: @@
   * Fine collector/filter
-Table Saw(s)
+===== Competencies =====
-  * Maintenance tag
-  * Dust gates
-  * Main power switches
-  * Power switches
-  * Paddle start/stop switch
-  * Fence (and locking lever)
-  * Riving knife
-  * Blade height adjust wheel
-  * Blade angle adjust
-  * Bypass mode turnkey
-  * Throat plate
-  * Riving knife lock lever
-  * Blade change wrenches
-  * Sleds
-===== Identify & mitigate common hazards =====
-  * Sharp things - cutting tools, chips, splinters
-  * Tangling hazard - no loose articles on the body, sleeves, gloves, or hand decorations (e.g. bracelets/rings)
-  * Heat - hot wood can cause burns, start fires
-  * Sound - hearing protection for louder operations
-  * Pinching/crushing and kickback hazard if wood not properly held or fed into the tool
-===== Allowable Materials =====
-  * Can name which tools are acceptable for cutting plastic
-  * Knows at least 2 materials which are prohibited (hint: any metal, and any composite that could cause a respiratory hazard)
-===== Safe Setup/Operation/Cleanup =====
-Miter Saw
-  * Demonstrate proper stock clamping and positioning of the blade for a straight cut
-  * Demonstrate performing a straight cut
-  * Demonstrate adjusting both angles of the chopsaw and making a cut
-  * Demonstrate locking and unlocking the horizontal slide
-Drill Press
-  * Demonstrate setting the speed and loading a drill bit
-  * Demonstrate proper material workholding and table adjustment
-  * Demonstrate drilling a hole in the stock material
-Bandsaw
-  * Demonstrate setting the blade height and proper stock holding
-  * Demonstrate cutting a piece of stock
-Belt/disk sander
-  * Demonstrate running the sander and sanding a part on both the belt and the disk
-  * Demonstrate cleaning the belt and disk with the rubber eraser
-Spindle Sander
-  * Demonstrate changing the spindle diameter
-  * Demonstrate sanding a piece of stock
-Scroll Saw
-  * Demonstrate loading a blade
-  * Demonstrate setting the foot
-  * Demonstrate adjusting the table
-  * Demonstrate cutting a piece of wood
-Dust Collector
   * Demonstrate turning the dust collector on and off
   * Demonstrate opening, emptying, and properly closing the main dust bin
+  * Knows to check the dust collector during extended operation to prevent buildup
-Table Saw(s)
+====== Drill Press ======
+{{section>tools:general_wood:drill_press_clearance#Tool Specific Instruction&title&noheader&nofooter}}
-  * Demonstrate loading/changing the blade and switching between the riving knife and the plastic guard
+====== Belt Sander ======
-  * Demonstrate setting the blade height for a specific piece of stock
+{{section>tools:general_wood:belt_sander_clearance#Tool Specific Instruction&title&noheader&nofooter}}
-  * Demonstrate using the fence and push blocks to cut a piece of stock
-===== Knowledge and Technique =====
+====== Spindle Sander ======
+{{section>tools:general_wood:spindle_sander_clearance#Tool Specific Instruction&title&noheader&nofooter}}
-Miter Saw
+====== Scroll Saw ======
+{{section>tools:general_wood:scroll_saw_clearance#Tool Specific Instruction&title&noheader&nofooter}}
-  * Acknowledges the keep-out zone of the saw must be observed
-Drill Press
-  * Shows good technique when feeding the drill bit into the part
-  * Knows when the bed should be adjusted to prevent damage to the machine
-Bandsaw
-  * Shows proper cutting technique to prevent the blade from binding/torquing
-Belt/disk sander
-  * Acknowledges that the tables should not be used as a resting spot for material or tools while the sander is running
-  * Knows how to properly hold and orient stock to prevent binding and kickback
-Spindle Sander
-  * N/A
-Scroll Saw
-  * N/A
-Dust Collector
-  * Knows to check the dust collector during extended operation to prevent buildup
-Table Saw(s)
+====== Miter Saw ======
+{{section>tools:general_wood:miter_saw_clearance#Tool Specific Instruction&title&noheader&nofooter}}
-  * Knows when to use the sled vs the fence
+====== Bandsaw ======
-  * Acknowledges that one should never use more than one guiding tool when operating the saw (kickback/binding risk)
+{{section>tools:general_wood:bandsaw_clearance#Tool Specific Instruction&title&noheader&nofooter}}
-  * Knows what bypass mode is, the process to enable it, and the increased risk of injury/kickback by operating in this mode
+====== Table Saw ======
+{{section>tools:general_wood:table_saw_clearance#Tool Specific Instruction&title&noheader&nofooter}}